Do you find yourself on the lookout for insight about How to Install a Bathtub?
Setting up a bathtub isn't precisely rocket science, but it does require strong plumbing, carpentry, as well as sometimes, tiling skills. Changing an old bath tub with a new one is additionally a moderately challenging job. If the old bathtub is easily obtainable, the project can relocate speedily; if you have to open up a wall surface to remove the old bathtub and position the brand-new bathtub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to move out the old bathtub and also set in the brand-new one. Make sure you have certified on your own for the job as well as fit trying it. Rather than hiring a specialist to take control of a halfway-completed task, it is better to think about utilizing one before you start. Opportunities are you might need an expert plumber to make tube links.
This write-up will help you set up a brand-new bath tub in your bathroom if you have already gotten a brand-new bathtub and don't need to alter the plan of your previous water pipelines.
Your tools and material checklist must consist of the following:
Getting ready for the Setup
First of all, the supporting frame supplied with the bath ought to be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to ensure that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of both taps utilizing 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its final placement.
Removing Old Touches
If you need to change old faucets with new ones as a part of your installation, after that the first thing you must do is detach the water supply. After doing so, activate the faucets to drain any kind of water staying in the system. The process of eliminating the existing taps can be quite bothersome as a result of the restricted access that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a towel ready for the continuing to be water that will originate from the pipes. When the supply pipes have actually been gotten rid of, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning throughout this procedure. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old securing substance.
Before carrying on to fit the new taps, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Installing the Tub
Using the two wood boards under its feet, place the bath tub in the required setting. The wood boards are useful in uniformly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four little factors.
The following goal is to make certain that the bathtub is leveled all round. This can be achieved by checking the level and also changing the feet on the bath tub until the spirit level reviews degree.
To install faucets, fit all-time low of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the very same for the other tap.
Turn on the water system and also examine all joints and new pipework for leaks as well as tighten them if required. Fill up the tub and likewise inspect the overflow outlet as well as the typical outlet for leaks.
Lastly, repair the bath paneling as described in the manufacturer's user's manual. Tiling and also securing around the tub should wait until the bath tub has actually been utilized at least once as this will certainly resolve it into its final setting.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly need a plastic port to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end supplies a link to the existing supply pipes.
If you require to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the installing opening in the bath/basin making sure that the washers are in area between the faucet as well as the sink. Secure the faucet in place with the manufacturer given backnut. When the tap is firmly in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet ports. The former kind ought to be attached to the faucet ends initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the location where the bath satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to crack a stiff seal, causing the water to permeate the wall surface between the bathroom and the tiling, causing complications with moisture and feasible leakages to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures and also fittings. They are offered in tubes and cartridges, as well as can securing voids up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always fill up the bath tub with water before securing, to allow for the motion experienced when the tub is in usage. The sealant can fracture fairly very early if you do not take into account this motion prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily readily available on the market. It is a good idea to fit the floor tiles using waterproof or water-proof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been made aware of that write-up on How to Install a Bathtub Yourself through someone on a different site. Do you know anybody else who is excited by the subject? Feel free to promote it. Thank you for going through it.
Check This Out